Chief WM210AUSI Instalační manuál

INSTALLATION INSTRUCTIONSWM-210SIWM-220SIWM-230SIWM-240SIDual Stud Short Throw Wall MountsSpanish Product DescriptionGerman Product Description Portug

Installation Instructions10INSTALLATION - (All Models)The WM2XXS/SI/AUS/AUSI short throw projector mounts canbe mounted to concrete, concrete block, w

Installation Instructions115. Install four 5/16 x 2-1/2" hex head lag screws (L) throughfour 5/16" washers (M), holes of wall bracket and in

Installation Instructions1210. Place wall bracket over anchors and align mounting holesin display mount with holes in anchors. (See Figure 12)11. Inse

Installation Instructions134. Loosen two bolts on either side of pitch adjustment screw.(See Figure 16)5. Adjust pitch adjustment screw until mount is

Installation Instructions14UL Listed RPA Installation1. Line up mounting holes on RPA mount with correspondingholes on projector mounting plate. (See

Installation Instructions154. Lower the upper cover (X) onto the wall mount and lowercover, and fasten with two 8-32 x 3/8" Phillips pan headscre

Installation Instructions16NOTE: Cables may be routed from below and up wall bracketchannel, or from above and down behind and into wallmount.• Routin

Installation Instructions1710. (Optional) Cables can be tied to inside of mount’s frontcover using cable ties (not included). Route cables nearfront c

Installation Instructions18AdjustmentsPitch AdjustmentIMPORTANT ! : The mount covers need to be removedbefore proceeding with pitch adjustment.NOTE: R

Installation Instructions19Security Screw Installation (Optional)Wall Bracket Covers1. Remove eight #8-32 x 1/2" Phillips pan machine screws (F)f

Installation Instructions2DISCLAIMERMilestone AV Technologies and its affiliated corporations andsubsidiaries (collectively "Milestone"), in

Installation Instructions204. Install two 8-32 x 3/8" button head security screws (AA) intolower cover. (See Figure 44)Figure 445. Replace upper

Installation Instructions212. Remove one of four bolts from adapter plate. (See Figure 48)Figure 483. Install one 1/4-20 x 3/4" button head secur

Installation Instructions22Cable Management (Optional)In most cases, cable management covers will NOT need to beremoved in order to route cables from

Installation Instructions23• Routing Cables from Above (Step 7)7. Thread cables down through a surface mount cableaccessory (not included), then behin

Installation Instructions241. Place wall bracket top caps (C) over top of each wall bracketarm. (See Figure 61)Figure 612. Secure wall bracket top cap

Installation Instructions25Extension Adjustment1. Loosen two bolts holding stop bracket in place on undersideof short throw projector mount. (See Figu

Installation Instructions26Mount Covers1. Remove two #8-32 x 1/2" Phillips pan machine screws (F)holding mount covers on projector arm. (See Figu

Installation Instructions27Adapter Plate Bolts1. Remove projector from short throw projector mountaccording to projector interface instructions.NOTE:

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378P 800.582.6480 / 952.894.6280F 877.894.6918 / 952.894.6918Europe A Franklinstraat 14, 60

Installation Instructions3TABLE OF CONTENTSDisclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Important Safety Instructions . .

Installation Instructions4DIMENSIONS10.817.25.75 16.0011.53.347.253.965.64210S, TRAVEL 12.75" - 19.5"240S, TRAVEL 37.2" - 65.6"3

Installation Instructions5LEGENDTighten FastenerApretar elemento de fijaciónBefestigungsteil festziehenApertar fixadorSerrare il fissaggioBevestiging

Installation Instructions6TOOLS REQUIRED FOR INSTALLATIONPARTS1/2" (12.7mm)#2 7/32" (5.6mm) 3/8" (9.5mm)3/16"(included)5/32"(

Installation Instructions7SITE REQUIREMENTS - Steel Stud Structure (All Models)WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SE

Installation Instructions8WS2XXSI/WS2XXAUSI INTERACTIVEMODELS ONLYThe Chief Interactive Mount (WM2XXSI/WM2XXAUSI) workswith standard projectors and Wi

Installation Instructions9WM2XXSI/WM2XXAUSI Placement andProjection Area Constraints (See Figure 3)• There should be a minimum distance of 12 inchesbe